Residential Electrical Services in Big Lake, MN
Wired Right From the Panel to the Last Receptacle
No point along a kitchen countertop sits more than 24 inches from a receptacle under NEC 210.52(C), so wiring gets planned before cabinets are ordered. Curtis C Contracting LLC builds that planning into every remodel, addition, garage and rebuild we manage in Big Lake, MN and Elk River. This page covers residential electrical services delivered through licensed electricians on our projects: panel and service upgrades, 20-amp appliance circuits, GFCI and AFCI protection, lighting layouts, EV charger circuits and whole-house rewires.
Every electrical scope runs under a State Board of Electricity permit with a rough-in and final inspection, performed by a licensed electrical contractor we schedule and coordinate as general contractor. We carry Minnesota residential building contractor license BC808587 and a BBB A+ accreditation, answer 24-hour emergency calls after storm, fire and water damage, and bring 30 years of hands-on framing and finish work to sequencing wiring ahead of drywall and trim. Quotes are free; request yours through our contact page.
Free Estimate!
For the fastest reply, call or text us 24/7 at
Contact Us
We will get back to you as soon as possible.
Please try again later.
Electrical Work We Coordinate and Complete
Panel and Service Upgrades
Additions and rebuilds push an older 100-amp panel past its limit, so the licensed electrician on the project sizes a new 200-amp service around the full load calculation. Upgrades at 200 amps or more may qualify for the Minnesota Commerce panel-upgrade rebate.
New Circuits and Receptacles
Kitchen remodels need two 20-amp appliance circuits feeding countertop receptacles placed within 24 inches of any point along the counter. We map each run on the cabinet drawings, then the electrician roughs boxes in before drywall and trims out after paint.
GFCI and AFCI Protection
Ground-fault protection has covered essentially every kitchen receptacle since the 2023 NEC, and arc-fault breakers protect bedrooms, living areas, hallways and laundry rooms. Extending an existing circuit more than 6 feet triggers AFCI too, which we flag during the remodel scope walk.
Kitchen and Bath Lighting Layouts
Lighting plans go onto the cabinet drawings so recessed cans, under-cabinet strips and vanity sconces land where the work happens. Switch legs, dimmers and bath fan wiring get roughed in with the layout, and damp-rated fixtures go over showers and tubs.
Garage, Shop and EV Charger Circuits
Detached garages and shops get a subpanel, with 240-volt circuits for compressors and welders where the plan includes a workshop. EV chargers run on a separate circuit sized at 125% of continuous load, so a 48-amp charger takes a 60-amp breaker.
Rewiring After Damage and Whole-House Rewires
Fire-scorched or water-soaked wiring comes out to the last junction box, and the rebuild gets new NM cable, boxes and devices under a fresh permit. Older homes with cloth-insulated or aluminum branch wiring get the same room-by-room replacement during whole-house remodels.
Why Choose Us for Electrical
One Point of Contact for Every Trade
You call us, and we call the electrician, the drywaller and the inspector. Scheduling, permit paperwork and the order of operations stay on our desk, so a change to the cabinet layout reaches the wiring plan before boxes get set, not after.
Permits Pulled and Inspections Scheduled
State Board of Electricity permits get filed before the first cable is pulled, and we book the rough-in inspection to land the day the electrician finishes. Walls stay open until the inspector signs, which protects you from tearing out new drywall later.
Sequenced Around Drywall and Finish
Wiring goes in after framing and before insulation, and we hold the schedule to that order so nobody cuts a finished wall to chase a missed circuit. Trim-out waits until paint dries, keeping devices and cover plates clean on the final walkthrough.
Panel Capacity Planned for the Whole Project
Before design is final, the electrician runs a load calculation for everything on the drawings: range, dryer, heat pump, EV charger and future shop. Sizing the service once for the full scope avoids a second panel upgrade when the next project comes.
Documented Work for Insurance Rebuilds
After a fire or flood, we photograph damaged wiring, itemize the replacement scope with the electrician's estimate and meet your adjuster on site to walk the findings. Interpreting the policy stays with your insurer; our job is the accurate record and the rebuild.
Dust Control and Daily Cleanup
Cutting boxes into plaster and fishing cable through finished ceilings makes dust, so we hang zipper walls, run air scrubbers and cover floors before the electrician starts. Each day ends with debris bagged, tools staged and every wall marked for the next trade.
Testimonials
See What Our Customers Are Saying!
Every Circuit Accounted For Before the Drywall Goes Up
A remodel is only as finished as the wiring behind its walls, and the best time to get that wiring right is while the studs are still exposed. Curtis C Contracting LLC manages the electrical scope on every kitchen, bath, addition, garage and rebuild we take on in Big Lake, MN, bringing in licensed electricians, filing the permits and standing beside the inspector at rough-in and final. If you are weighing a panel upgrade, a new shop circuit or a full rewire of an older home, there is no pressure to decide today; ask questions first and compare notes. Once you are ready, request a free quote through our contact page and we will walk the project with you.
Frequently Asked Questions
How many amps does a house need?
A 200-amp service is the standard target for a modern house, while many older homes run on 100 amps. Adding a heat pump, an EV charger or an addition pushes the load calculation past 100, which is when a service upgrade makes sense.
Why does my breaker keep tripping?
Repeated tripping means the circuit is overloaded, a device is shorting or the breaker itself has worn out. Kitchens on a single old circuit are the usual culprit, and the fix during a remodel is splitting loads onto new 20-amp runs.
How many outlets can be on one circuit?
The NEC sets no fixed count for general-purpose receptacles in a home; the limit comes from the load the circuit serves. Countertop receptacles are the exception, needing two reserved 20-amp circuits. Electricians on our projects size each run to the actual load.
Do I need a permit to add an outlet?
In Minnesota, yes, adding a receptacle requires a State Board of Electricity permit, pulled by the licensed electrician, then inspected. On Curtis C. Contracting remodels in Big Lake, MN, that permit gets filed alongside the building permit so both inspections line up.
What is the difference between GFCI and AFCI?
GFCI devices sense current leaking to ground and cut power to stop shocks, which is why kitchens, baths and garages require that protection. AFCI breakers detect arcing inside damaged cable or loose terminals to stop fires, covering bedrooms, living rooms and hallways.
How do I know if my house wiring is outdated?
Warning signs include two-prong outlets, a fuse box instead of breakers, cloth-covered cable, warm cover plates and lights that dim when the furnace kicks on. Houses built before 1980 deserve a close look at the branch wiring before any remodel closes the walls.
What size panel do I need for an EV charger?
Under the NEC's 125% continuous-load rule, a 48-amp Level 2 charger needs a 60-amp circuit and a 40-amp plug-in unit needs 50 amps. Older 100-amp panels rarely absorb that on top of existing loads, so a 200-amp service often accompanies the charger.
How long does it take to rewire a house?
Rewiring a house during a remodel runs several weeks, because cable gets fished room by room, then inspected before drywall patches close. Curtis C. Contracting sequences that work in Big Lake, MN with the other trades so wiring never stalls the finish schedule.